S&S Swan Maintenance - Thread List

New Thread
Thread Title / User / Date Last post Replies Views Replies / Views
David Carne Vang
Candy Morganson - 22 September 2013 - 22:44
29 September 2013 - 19:21
By: robmably
4 1376 4 / 1376
Hatch covers swan 38
cocatrix - 18 September 2013 - 08:08
18 September 2013 - 13:47
By: cocatrix
2 1182 2 / 1182
Electric winches - good idea.
Boat441 - 21 August 2013 - 14:45
09 September 2013 - 11:17
By: CLA7003
7 1775 7 / 1775
Shaft Log
ccolton - 02 September 2013 - 17:35
02 September 2013 - 17:38
By: ccolton
1 1187 1 / 1187
Cowl vent
cocatrix - 12 August 2013 - 20:11
26 August 2013 - 18:51
By: cocatrix
2 1319 2 / 1319
Perkins 4.108 gaskets and seals installed
ccolton - 18 July 2013 - 19:59
18 July 2013 - 19:59
By: ccolton
0 1200 0 / 1200
Bamar Hatch rebuild
ccolton - 25 March 2013 - 16:07
18 July 2013 - 19:56
By: ccolton
11 1744 11 / 1744
Trim Tab quadrant needed for 43
ccolton - 17 July 2013 - 19:41
17 July 2013 - 19:41
By: ccolton
0 1158 0 / 1158
Velvet drive motor mounts
ccolton - 22 June 2013 - 16:12
22 June 2013 - 16:12
By: ccolton
0 1274 0 / 1274
Shower on a 37
aussie - 20 June 2013 - 19:32
21 June 2013 - 11:48
By: the professor
2 1228 2 / 1228
Propeller and gearbox for a 37
aussie - 20 June 2013 - 19:43
21 June 2013 - 11:41
By: the professor
1 1228 1 / 1228
Swan 37 tankage
Aussie - 02 June 2013 - 21:14
11 June 2013 - 22:52
By: Aussie
4 1263 4 / 1263
Perko Raw Water Intake Strainer
ccolton - 24 April 2013 - 13:15
10 June 2013 - 17:08
By: ccolton
4 1374 4 / 1374
Swan 44 pipe cot hinges
the professor - 24 May 2013 - 13:17
01 June 2013 - 17:45
By: philippeV
10 1427 10 / 1427
Inside or Outside repair patch on mast
Anthea - 31 May 2013 - 17:03
01 June 2013 - 17:01
By: anthea
3 1217 3 / 1217
forward hatch for 37
aussie - 31 May 2013 - 01:00
31 May 2013 - 01:00
By: aussie
0 1208 0 / 1208
Mast and steel frame repair
martin - 23 May 2013 - 21:07
30 May 2013 - 07:27
By: martin
6 1426 6 / 1426
Mabel's Casse Tete 43/003 needs trim tab quadrant
ccolton - 28 May 2013 - 15:43
29 May 2013 - 21:00
By: ccolton
4 1256 4 / 1256
Vibration / knocking at rpm over 2,000
Outrageous - 19 May 2013 - 08:02
19 May 2013 - 11:18
By: the professor
1 1259 1 / 1259
Polishing hull
franchivittorio - 13 May 2013 - 20:30
17 May 2013 - 13:27
By: ccolton
3 1539 3 / 1539